MODEL : Jus’ Bill RP-35
Mini Dot Impact Printer
All specifications are subject to change without notice
Table of Contents
1. Features
3
4
2. Specification
3. Self Test
6
4. User Switches
7
5. Command List
8
5.1. EMULATION EPSON TM-U200
5.2. EMULATION CITIZEN iDP-3540
5.3. EMULATION STAR SP200
6. Interface
8
9
10
11
11
13
14
15
6.1. Interface Connector
7. Cash Drawer Connector
8. Electrical Specifications
9. Dip Switch Settings
2
1. Features
♣Dip Switch Configuration
Emulation mode, communications mode, baud rate, serial/parallel handshake, and head printing
characteristics are all configured through dip switch settings.
♣Data Buffer
The Jus' Bill RP-35 printer has a built-in 16 Kilobyte I/O buffer allowing the host computer to free itself
after sending the print data.
♣Reliable communications
The Jus' Bill RP-35 supports multiple baud rates, protocols, and handshaking on its parallel & serial
interfaces.
♣User controls
A power switch, a paper feed switch, power LED and Paper Low/Out error LED provide ease of use.
♣Self Test Mode
A comprehensive self-test mode is available which describes the printer configuration and dip switch
setting information along with the version number of firmware installed.
♣Print orientation
The printer is capable of printing normal and upside down, the print orientation is selected by software
commands.
♣Selectable international characters
The Jus' Bill RP-35 supports international characters selectable by software control.
♣Multiple Fonts/Sizes
Two different resident fonts are available for printing diversity. Each of these fonts can be printed in
normal, double wide, double height, and quadruple sizes. Both fonts and sizes are software selected.
♣Bit image graphic
Two formats for bit mapped graphics are provided.
♣Error detection
The Jus' Bill RP-35 can detect paper-out and paper-jam as well as paper near-end, controller malfunction,
and cover open status.
♣Peripheral Drive
Two cash drawer drivers are provided.
♣Certification
(1) This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
1) this device may not cause harmful interference , and
2) this device must accept any interference received , including interference that may cause
undesired operation.
(2) UL/cUL (UL 60950-1)
(3) MIC
(4) CE-EMCD (CE-EMCD Class B should use Parallel shield Cable complied with IEEE-1284 standards)
(5) RoHS (TUV)
(6) CCC
3
2. Specification
Printer Specifications
MODEL
Jus' Bill RP-35
PRINT METHOD
PRINT DIRECTION
NO. OF COLUMNS
9-pin serial impact dot matrix
Bi-directional (with logical seeking)
Epson Mode : 42/35, 40/33, Star Sp200 : 42/35
Other Modes : 40/32
7 x 9, 9 x 9 dots
FONT SIZE
LINE SPACING
PRINTING WIDTH
PRINT SPEED
INK RIBBON
n/144 inch
63.5mm (2.5”)
5 Line / Sec (at 40 cpl)
EPSON, ERC-38 compatible
Black or Purple, Black/Red
Roll Paper
PAPER
Media
Width
76.2mm (3.0”)
Diameter
76mm (3.0”) max.
3-ply max. (0.2mm or 0.008” thick)
One Original and one copy
Copies
DATA BUFFER
16K bytes
CASH DRAWER DRIVER
2 circuits (24V, 1A max)
RS-232C Serial (25Pin)
USB
USB Combo
Ethernet
INTERFACE
Wireless Lan
Centronics Parallel (36Pin)
EMULATION
Epson TM-U200, Citizen iDP-3540
Star SP200
POWER SUPPLY
Type
External Adaptor
Input
120VAC, 230VAC
Output
24VDC X 2.5A
OPERATING CONDITION
STORAGE CONDITION
5°C to 40°C, 10% to 80% RH
-20°C to 60°C, 5% to 95% RH
18 million lines
RELIABILITY
DIMENSIONS
WEIGHT
MCBF
Printhead
Cutter
150 million characters
157(W) X 245.12(D) X 153.1(H)mm
157(W) X 245.12(D) X 153.1(H)mm
5.24 lbs (2.38 kg)
Non cutter
Cutter
Non cutter
4.96 lbs (2.25 kg)
4
Overall dimension
5
3. Self Test
While pressing the paper feed switch for more than 10 seconds after the printer in turned on, the self
test mode is initiated.
The printer self test includes a listing of the current default settings, read and write test of internal RAM,
checksum test of internal program memory, loop back detection statement, a staggered dot line, a few
lines of rotating character set, and a diagnostic report.
The printer then enters into the On-Line mode.
Configuration Setup
When the paper FEED switch is pressed and released instantly as the power is applied to the printer, the
printer will print the current printer configuration settings along with the DIP switch information.
If the printer setup needs to be changed, turn the Power Off before changing the setting.
The printer will be setup at the factory as follows;
Printer is setup as follows:
Model :
Jus' Bill RP-35
Ver X.XX
Serial
Epson TM-U200
CR=CR only
DTR/DSR
Firmware :
Interface :
Emulation :
CR Character :
Flow Control :
Data Bits :
Parity :
8 Bits
None
Baud Rate :
CPL :
Two Color :
Auto Cutter :
Journal :
9600
40/33 Char / Line
Installed
Installed / Not Installed
Installed / Not Installed
6
4. User Switches
Panel Switches
Paper Feed button : Pressing the PF button momentarily will advance the paper one character line and
pressing it continuously will cause a fast feed at 15 lines per second.
Power Switch
A Power switch located on the lower left side of the printer is used to turn the printer on/off.
Indicators
This section explains the different patterns signaled by the two LED indicators located on the top cover
of the Jus' Bill RP-35.
LED1
GREEN
OFF
Flash
ON
LED2
RED
OFF
ON
LED3
RED
OFF
ON
STATUS
REMARKS
Power Off
Power On
On line
Normal power is not supplied to the printer
Normal power is supplied to the printer
Normal error-free mode
OFF
OFF
Flash
Flash
OFF
ON
OFF
ON
Paper low
Cover open
Paper empty
ON
Insert new paper roll
ON
OFF
OFF
Close cover
ON
Insert new paper roll
ON
Paper jam
Test mode
OFF
OFF
Impossible to recover
Ignored Paper Low
OFF
ON
ON
7
5. Command List
5.1. EMULATION EPSON TM-U200
Command
HT
Hex Code
<09>H
Description
Horizontal tab
LF
<0A>H
Print and line feed
CR
<0D>H
Carriage Return
DLE EOT
DLE ENQ
ESC SP
ESC !
ESC %
ESC &
ESC *
ESC -
ESC 2
ESC 3
ESC <
ESC =
ESC ?
ESC @
ESC D
ESC E
ESC G
ESC J
ESC R
ESC U
ESC a
ESC c 4
ESC c 5
ESC d
ESC p
ESC t
<10>H<04>H<n>
<10>H<05>H<n>
<1B>H<20>H<n>
<1B>H<21>H<n>
<1B>H<25>H<n>S
<1B>H<26>H
<1B>H<2A>H
<1B>H<2D><n>
<1B>H<32>H
<1B>H<33>H<n>
<1B>H<3C>H
<1B>H<3D>H<n>
<1B>H<3F>H<n>
<1B>H<40>H
<1B>H<44>H<n>
<1B>H<45>H<n>
<1B>H<47>H<n>
<1B>H<4A>H<n>
<1B>H<52>H<n>
<1B>H<55>H<n>
<1B>H<61>H<n>
<1B>H<63>H<34>H<n>
<1B>H<63>H<35>H<n>
<1B>H<64>H<n>
<1B>H<70>H
<1B>H<74>H<n>
<1B>H<7B>H<n>
<1D>H<49>H<n>
<1D>H<61>H<n>
<1D>H<72>H<n>
Real-time status transmission
Real-time request to printer
Set right-side character spacing
Set print mode
Select/cancel user-defined character set
Define user-defined characters
Select bit-image mode
Turn on/off underline mode
Select 1/6 inch line spacing
Set line spacing
Return home
Select peripheral device
Cancel user-defined characters
Initialize printer
Set horizontal tab positions
Turn on/off emphasized mode
Turn on/off double-strike mode
Print and feed paper
Select an international character set
Turns on/off unidirectional printing mode
Select justification
Select paper sensor to stop printing
Enable/disable panel button
Print and feed n lines
Generate pulse
Select character code table
Turn on/off upside-down printing mode
Transmit printer ID
Enable/disable Automatic Status Back
Transmit status
ESC {
GS I
GS a
GS r
8
5.2. EMULATION CITIZEN iDP-3540
Command
BEL
CAN
LF
Hex Code
<07>H
<18>H
<0A>H
Description
Drive pulse setting command for 1st drawer
Clear data in buffer
Paper feed
FF
CR
<0C>H<n>
<0D>H
Paper feed n lines
Print command
SO
SI
DC1
<0E>H
<0F>H
<11>H
Select expanded character mode
Select normal character mode
Initial set command
DC2
<12>H
Inverted print mode
DC3
ESC BEL
SUB
<13>H
<1B>H<07>H<n>
<1A>H
Red color print command
1st drawer driver command
2nd drawer driver command
Select underline mode
Graphic command
Set 1/9 inch line feed
Set 2/9 inch line feed
Set page length
n line skip perforation command
Cancel skip perforation command
Select full-cut / partial-cut
Form feed
ESC -
ESC *
ESC 1
ESC 2
ESC C
ESC N
ESC O
ESC P
ESC f
FS
<1B>H<2D>H<n>
<1B>H<2A>H<n>
<1B>H<31>H
<1B>H<32>H<n>
<1B>H<43>H<n>
<1B>H<4E>H<n>
<1B>H<4F>H
<1B>H<50>H<n>
<1B>H<66>H
<1C>H
1st drawer drive command
9
5.3. EMULATION STAR SP200
Command
BEL
Hex Code
<07>H
Description
Differed drive command “A” for peripheral unit
(Default setting)
CAN
LF
CR
SO
SI
<18>H
<0A>H
<0D>H
<0E>H
<0F>H
<1C>H
<14>H
Cancel print data in buffer
Line feed
Line feed (same as LF)
Select expanded character mode
Cancel expanded character mode
Immediate drive command “B” for peripheral unit 1
Cancel expanded character mode
FS
DC4
ESC BEL
n1 n2
Adjust drive pulse width for peripheral unit
(Default setting)
<1B>H<07>H<n1><n2>
<1B>H<40>H
ESC @
Initialize printer
Select 7 x 7 (Half dots) character size
(Default setting)
ESC M
<1B>H<4D>H
ESC R n
ESC P
<1B>H<52>H<n>
<1B>H<50>H
Select international character set
Select 9 x 7 (Half dots) character size
<1B>H<57>H<31>
H<1B>H<57>H<1>
<1B>H<57>H<37>
H<1B>H<57>H<0>
ESC W 1
Select expanded character mode
ESC W 0
ESC a n
Cancel expanded character mode
Feed paper n lines
<1B>H<61>H<n>
10
6. Interface
6-1. Interface Connector
<D-SUB 25 Female Serial>
<Centronics Parallel>
<USB “B” Type>
<Ethernet>
<USB COMBO>
Serial Interface
<Wi-fi>
PIN
SIGNAL
TXD
RXD
DTR
DSR
I/O
Output
Input
Output
Input
-
DESCRIPTION
Printer transmit data line RS-232C level
Printer receive data line RS-232C level
Printer handshake to host line RS-232C level
Data Send Ready
2
3
4, 20
6
1, 7
GND
System Ground
USB Interface
PIN
SIGNAL
+5V
DATA-
DATA+
GND
I/O
DESCRIPTION
+5V
Printer transmit data line
Printer transmit data line
System Ground
1
2
3
4
-
-
-
-
11
Centronics Parallel Interface
PIN SIGNAL
STROBE-
I/O
Input
Input/Output
Output
Output
Output
DESCRIPTION
Synchronize signal Data received
Data bit Transmitted 0~7
Data receiving completed.
Impossible to print of data receiving.
Paper empty
1
2~9
10
DATA0~7
ACK-
11
BUSY
12
PE
13
14
15
16
SELECT
AUTO FEED-
GROUND
GROUND
NC
Output
Input
-
-
Printer status for ON/OFF line
Paper auto feed signal
System ground
System ground
17
-
18
19~30
31
LOGIC-H
GROUND
INIT-
-
-
+5V
System ground
Initialize
Input
32
33
34
35
ERROR-
GROUND
NC
Output
-
-
-
Printer error
System ground
+5V
+5V
36
SELLECT IN-
Input
Printer select signal
Ethernet Interface
PIN
1
2
SIGNAL
I/O
Data Out +
Data Out -
GND
Output Data +
Output Data -
Ground
3
4
5
6
Data IN +
Data IN -
N.C
Input Data +
Input Data -
7
N.C
8
N.C
12
7. Cash Drawer Connector
The Jus' Bill RP-35 can operate two cash drawers with a 6 pin RJ-11 modular connector. The driver is
capable of supplying a maximum current of 1.0A for 510 ms or less, when not printing.
<Cash Drawer Connector>
PIN
1
SIGNAL
Signal GND
DESCRIPTION
-
2
3
4
Drawer kick-out drive signal 1
Drawer open/close signal
+24V
Output
Input
-
5
6
Drawer kick-out drive signal 2
Signal GND
Output
-
13
8. Electrical Specifications
The Jus' Bill RP-35 requires a power supply with the following parameters.
A linear power Adapter is included in the Jus' Bill RP-35 box.
Power Supply Voltage : 24VDC±10%
Power Supply Current : 2.5 A
<Power Supply Connector>
14
9. Dip Switch Settings
This table gives the definition for the DIP switch settings.
SW1
Function
Setting
1
2
3
4
5
6
7
8
Epson TM-U200
Epson TM-U300
Citizen iDP3540
Star SP200
OFF
ON
OFF
ON
OFF
OFF
ON
ON
Emulation
········
CR
Character
CR=CR Only
CR=CR + LF
OFF
ON
40/33
Char/Line
42/35
OFF
ON
CPL
Char/Line
Auto
Cutter
Not Install
Install
OFF
ON
Not Install
Install
OFF
ON
2Color
Journal
S
E
R
I
A
L
Not Install
Install
OFF
ON
SW2
Function
Setting
1
2
3
4
5
6
7
8
Flow
Control
DTR/DSR
Xon/Xoff
OFF
ON
38400
19200
9600
OFF
ON
OFF
ON
OFF
OFF
ON
ON
Baud
Rate
4800
8 Bits
7 Bits
OFF
ON
Data Bits
Parity
None
Odd
-
OFF
ON
ON
OFF
ON
Even
Auto
Melody
Not Install
Installed
OFF
ON
15
SW1
Function
Setting
1
2
3
4
5
6
7
8
Epson TM-U200
Epson TM-U300
Citizen iDP3540
Star SP200
OFF
OFF
ON
ON
OFF
ON
OFF
ON
Emulation
CR
Character
CR=CR Only
CR=CR + LF
OFF
ON
P
A
R
A
L
40/33 Char/Line
42/35 Char/Line
OFF
ON
CPL
Auto
Cutter
Not Installed
Installed
OFF
ON
L
E
L
Not Installed
Installed
OFF
ON
2 Color
Journal
Not Installed
Installed
OFF
ON
SW2
Function
Setting
1
2
3
4
5
6
7
8
Auto
Melody
Not Install
Installed
OFF
ON
16
17
Rev. 1.0
|